37' Pacific Proa
by Russell Brown
featured in Wooden Boat Magazine
July/August, 1988, Issue #83
RUSSELL BROWN and His PROVEN PROAS
- A truss box beam suspended to weather between the crossbeams and supporting the mast base. All controls lead to this
centralized location including rudder up/downhauls.
- Two separate steering levers, each connected to respective rudders by aluminum poles. The rudder on the port bow
is visible in the raised position (as it would be on port tack).
- A continuous red line passes each steering lever and enters the interior where it is connected to a conventional electronic
autopilot for tillers. The red line is normally engaged only to the aft
tiller/rudder in the lowered position and easily disengaged from both.
- Headsail halyards for each bow share the same winch on the mast.
- A continuous mainsheet attached at each end to the end of the boom passes fore and aft around the mast base winches
and leads through two movable fairleads at each end of the boat: 1) on
a special spar that brings the boom parallel to the centerline (pictured
in Helm Station photo) and 2) outboard to leeward for letting
the boom out parallel to the crossbeams.
- Carpet attached to mast with simple yoke on boom that rotates 180 degrees each tack.
- Motor mount and fuel cans to weather of mast base; lowers 20 HP outboard to water.
- Chimney for wood stove.
- Knife pockets near hatch for cutting away jammed lines quick!
- Below decks, a comfortable wood stove keeps things cozy through bitter New England winters.
- The red line below the hatch and fire extinguisher attaches to the electronic autopilot (left of photo) and to the steering levers outside.
- The bench seat has access hatches for storage below.
- The table folds down against the leeward side of the boat (the blue air mattress is on the main double berth in the lee "pod").
- The bulkhead beyond the table gives access to storage, head, etc.
- View towards starboard bow.
- Double berth lee pod on left with stove (tea kettle) at one end.
- Galley sink on right, below and "forward" of main hatch.
- Sprout grower above sink.
- Folding single seat attached to left (leeward) side
- Navigation and comm station forward of main bulkhead, one of two primary bulkheads showing attachment bolts for crossbeams.
- Smaller access hatch in forward bulkheads make bows watertight when under way.
- Main sail stored on cabin sole for winter haulout.
Leeward Pod with double berth
JZERO of Polygor, 1977
- photos by Craig Bumgarner
- JZERO of Polygor, 1978
Sailing to Puerto Rico with Russ Brown
by Mark Balogh
- Park It, Dad
by Jim Brown - Russell and Jim sail KAURI from Bermuda to New England *Sep, 2011
- CIMBA (re-named Pacific Bee in 2008) and JZERRO
- JZERRO Construction Photos
Port Townsend, WA 1992 by Joseph Oster
- JZERRO Mexico Photos...
36' Pacific proa, Baja California (Mexico)
- a sailing 'push me-pull you' JZERRO
article by Andy Turpin, Latitude38
- JZERRO "doing about 20 knots"
on S.F. Bay, passing Profligate,
Dave Culp and Joseph Oster visible on bench seat, Latitude38
- Photos! Sailing JZERRO on San Francisco Bay
Russell Brown, Jim Antrim and Joseph Oster, June, 2000
- Russell Brown on Proas interview w/ John Harris at clcboats.com
"Jzerro will reach at 17 or 18 knots in 12 knots of wind."
- Observations on Pacific proas by Russell Brown, 3 Sep 2011
JZERRO on video
Pacific Proa Jzerro in Port Townsend - September 2012
Jzerro underballasted and hard on it
Proa Jzerro September, 2011
sailing 17.8 knots on auto-pilot!
*posted May, 2011
sailing 17.8 knots on auto-pilot!
sailing past lighthouse
*posted July, 2008 (not HD)
Port Townsend Watercraft,